Low Profile Floor Jack Fit Checker

Low profile floor jack clearance is simple: a jack fits if its stated minimum saddle height, plus any pad, is no taller than the gap under your jacking point, and it is useful if its stated maximum reaches your jack stand height. Enter both measurements below to check 17 spec-verified jacks.

1. Park on level ground.
2. Locate the jacking point in the vehicle owner’s manual.
3. Measure the vertical distance from the ground to that point. This is your clearance (C).
4. Take the target lift height (T) from the manual or label of the jack stand you intend to use, measured at the stand’s contact point.
5. If you will use a saddle pad or adapter, measure its thickness (P). Leave it at 0 or blank if you will not.
6. Choose inches or millimeters, enter the numbers and select Check fit.

Results are grouped as Meets both, Clears but stated max is below target, or Does not clear, and sorted by clearance margin within each group. The order is not a ranking or a recommendation. This page gives no clearance or stand-height numbers of its own; always use your vehicle and stand makers’ figures.

Each jack is tested with two plain comparisons using the saddle heights the maker states on the listing:

• Clears: stated minimum saddle height + pad thickness ≤ your clearance.
• Reaches: stated maximum saddle height ≥ your target lift height. The pad is deliberately not credited to reach, which is the conservative reading.
• Clearance margin = clearance − (minimum + pad); reach margin = maximum − target.

Unit conversion uses 1 in = 25.4 mm exactly. Capacity is shown as the explicit pound figure from the listing, with kilograms at 1 lb = 0.45359237 kg. Example with a clearance of 3.5 in, a target of 14 in and no pad:

“Low profile” is a marketing label, not a height. In our 17 verified listings, stated minimum saddle heights run from 2.75 in to 5.1 in, so two jacks both sold as low profile can differ by more than 2 inches at the bottom. If your measured clearance is below 2.75 in, the tool tells you that no jack in our dataset starts that low.

“Long reach” listings in the dataset state the largest maximum heights, up to 24.375 in. The checker compares only stated heights; it does not cover jack length or chassis width against your approach path, front lip or wheel position, suspension position, or whether a point is a legitimate lift point.

Watch the word “ton”. Some listings mean US short tons (2,000 lb) and others metric tonnes (1,000 kg, about 2,204.6 lb): a “3 ton” spec block can sit beside a title saying 6,600 lb. That is why the tool shows only the explicit pound figure and never converts a bare “ton” label. Matching rated capacity to your vehicle’s weight is outside this check; follow the maker’s rating and manual.

The dataset starts from our shelf snapshot of 2026-09-27: 43 non-sponsored rows for the query “low profile floor jack”, plus any floor jack titled low profile from related queries. Of 37 low profile floor jack rows, 17 met the inclusion criteria: explicit pound capacity, both saddle heights, and no conflicting specifications between title, bullets and spec block (tolerance 0.15 in or 1%). Six listings that contradicted themselves and 14 with a missing height or only an ambiguous “ton” capacity were excluded. Each kept value was read from its Amazon product page on 2026-10-12. The shelf is a sample, not the whole market.

Safety context: an NHTSA/NCSA research note on CPSC emergency-room data from 1994–95 (old data) states: “Approximately three-fourths (74%) of the persons injured in motor vehicle jack failures were injured as a result of being struck by the vehicle as it fell from the jack.” A 1999 NIOSH FACE report on a 37,500 lb transit bus on shop-made stands (not a car) states: “A 48-year old male mechanic (decedent) died when he was crushed by a bus that fell off jack stands.” Its recommendation was to “ensure employees use only tools and equipment that have been tested, certified and rated.” The cited sources do not provide an official US fatality count for jacks or jack stands. Never work under a vehicle supported only by a jack. Follow the jack and stand makers’ ratings and manuals and ASME PASE; this tool checks stated dimensions only and is not a safety rating.

• Amazon product pages – stated capacity and saddle heights for 17 listings (ASINs shown in the tool), read 2026-10-12
• Wikipedia: Inch – 1 in = 25.4 mm
• Wikipedia: Pound (mass) – 1 lb = 0.45359237 kg
• Wikipedia: Short ton and Tonne – ton definitions
• NHTSA/NCSA Research Note, September 1998: Injuries Associated With Hazards Involving Motor Vehicle “Jack Failures”
• NIOSH FACE Report 99CA006
• ASME PASE – Safety Standard for Portable Automotive Service Equipment (cited by name and scope)

Last updated: October 2026

• 10 Best 12-Ton Low-Profile Bottle Jacks
• 14 Best 20 Ton Low Profile Bottle Jacks
• Bottle Jack vs Floor Jack: Which One for Trucks, SUVs and Cars?
• 12 Best Low Profile Creepers with Headrest
• 11 Best Low Profile Creepers with Lights
• How to Maintain a Floor Jack: A Simple Routine for a Longer Life